What causes the bag filter to clog during use?
- Categories:Product knowledge
- Author:
- Origin:
- Time of issue:2020-01-10
- Views:0
(Summary description)It is reported that air infiltration often occurs in the flange of the dust catcher, access door or dust catcher's mobile device, if the seal is not strict, the external air into the dust catcher, when dealing with high temperature flue gas, will produce low temperature area in the dust catcher interior, resulting in low temperature dedew, corrosion dust catcher, resulting in the paste bag of filter bag or plate.
What causes the bag filter to clog during use?
(Summary description)It is reported that air infiltration often occurs in the flange of the dust catcher, access door or dust catcher's mobile device, if the seal is not strict, the external air into the dust catcher, when dealing with high temperature flue gas, will produce low temperature area in the dust catcher interior, resulting in low temperature dedew, corrosion dust catcher, resulting in the paste bag of filter bag or plate.
- Categories:Product knowledge
- Author:
- Origin:
- Time of issue:2020-01-10
- Views:0
Bag filter is one of the most commonly used filters. There will be blockage in the use of the filter. So what causes it? Let's take a brief look at it below.
1. Poor ash cleaning of filter bag
It is understood that if the bag filter ash frequently, or the cleaning time is too long, resulting in excessive equipment pressure, it is easy to make the fiber fabric of the filter bag loose, thus increasing the fine dust in the flue gas and blocking the filter bag. In addition, if the cleaning time is too long, the initial powder layer on the surface of the filter bag will also be cleaned, resulting in the decrease of the filter bag filtration accuracy. However, the dust cleaning time is too short, and the dust on the surface of the filter bag is not completely clean, so filtration begins immediately, and the dust gradually accumulates on the surface of the filter bag, which will also cause the filter bag blockage.
2. Contains water
Moisture is the main cause of filter bag clogging, which is usually caused by condensation at low temperature, especially when dealing with flue gas at high temperature. For this situation, you can use the following methods to prevent: avoid improper boot; Avoid starting the dust collector when the resistance is high; Boot below dew point. If the dust collector operates below the dew point, it is easy to cause problems. If the air intake is not evenly distributed, it is easy to cause local corrosion of the dust collector shell. Therefore, the dust collector should avoid working below the dew point. If starting at a low temperature is unavoidable, an insulation device such as steam or electric heating should be used.
3. Air penetration
It is reported that air infiltration often occurs in the flange of the dust catcher, access door or dust catcher's mobile device, if the seal is not strict, the external air into the dust catcher, when dealing with high temperature flue gas, will produce low temperature area in the dust catcher interior, resulting in low temperature dedew, corrosion dust catcher, resulting in the paste bag of filter bag or plate.
4. High filtering wind speed
It is understood that if the filter wind speed of the dust catcher operation exceeds the design standard of the filter bag, it will also lead to the fine dust in the flue gas into the fiber of the filter bag, resulting in increased blocking resistance of the filter bag.
Scan the QR code to read on your phone
Recommended reading
- Operating and maintenance instructions for screen filters 2019.06.29
- Common faults of electric lubrication pump and its elimination method I 2019.09.23
- What causes the bag filter to clog during use? 2020.01.10
- Causes of serious damage to hydraulic pumps 2020.02.28
- Where is the difference of lubricating pump unit price? 2019.03.29
- Taizhou electric lubricating pump manufacturer elaborated the cable connection problem 2019.06.11
- What should be done when the bearing temperature of hydraulic lubrication pump is too high 2019.06.11
- What is a multi-point electric oil pump for? 2019.07.19
- Kai Tian hydraulic equipment Co., LTD. Tell you: caused by the hydraulic fault how to find 2018.09.10
- Dry oil lubrication pump system installation notes 2018.10.16
Add:No. 1, Building 45b, North Chuangrong Industrial City, Yucheng Sub-district, Yuhuan City, Zhejiang Province
Zip:317600
Tel:0576-87234521
Fax:0576-87234522
Contact person: Manager Zhao
Mobile phone no.:13967670889
Email:office@kaitianyeya.com
Web:www.kaitianyeya.com
Copyright © Yuhuan Kaitian Hydraulic Lubrication Equipment Co., Ltd. 浙ICP备16006032号 Power:300.cn