Kaitian Lubrication to Lubricate Things Silently
location:
Homepage
/
/
/
What should be done when the bearing temperature of hydraulic lubrication pump is too high

What should be done when the bearing temperature of hydraulic lubrication pump is too high

  • Categories:Industry dynamic
  • Author:开天液压润滑设备
  • Origin:
  • Time of issue:2019-06-11
  • Views:0

(Summary description)What should be done when the bearing temperature of hydraulic lubrication pump is too high

What should be done when the bearing temperature of hydraulic lubrication pump is too high

(Summary description)What should be done when the bearing temperature of hydraulic lubrication pump is too high

  • Categories:Industry dynamic
  • Author:开天液压润滑设备
  • Origin:
  • Time of issue:2019-06-11
  • Views:0
Information

Hydraulic lubrication pump at run time, and sometimes, we will find it will overflow valve regulating failure, in this case, the causes of equipment is not normal, so, we need in a timely manner to make the corresponding countermeasures, the general failure, there are two one is to adjust pressure regulating handwheel pressure build up, or pressure can not meet the set value; The other is the hand wheel pressure is not down, or even continuous pressure rise. Pressure regulating failure, in addition to the spool radial clamping, there are the following reasons.

A. The damping hole on the main valve core is blocked, and the hydraulic pressure cannot be transferred to the upper cavity of the main valve and the front cavity of the cone valve, so the guide width will lose its regulating effect on the pressure of the main valve. Because the main valve chamber has no oil pressure and the spring force is very small, the main valve becomes a straight relief valve with very small spring force. In the case of low oil inlet chamber pressure, the main valve core will open the overflow and the system will not be able to establish the pressure. The pressure regulating spring is out of shape or the wrong selection, the leakage in the valve is too large or the guide valve cone width is too worn, etc., which are the basic reasons for the pressure not to reach the fixed value.

B. lubrication pump pilot valve cone seat damping hole jam, cone valve, hydraulic transmission is less than the same pilot valve has lost the adjustment role of the main valve pressure, the damping holes blocked, under no pressure, cone could not open the drain valve, there is no oil flow in the valve, the main valve core on inferior vena oil pressure are equal, the main valve core under the task of spring force in the closed state, can not overflow, overflow valve before the valve pressure rise with the increase of load. When the shearing machine actuator moves to the end point, the external load increases infinitely, and the pressure cylinder of the system increases infinitely.

C. If there is a pressure regulating valve in the remote control of the relief valve of the hydraulic lubrication pump, if the control port is blocked, the pipeline from the control port to the pressure regulating valve is long and there is human air, resulting in abnormal pressure regulation.

D. The sealing ring in the relief valve is damaged, and the main spool and cone spool are worn too much, causing serious leakage inside and outside, making the regulating pressure unstable and even unable to work normally.

Lubrication pump overflow valve failure reasons, can be roughly divided into four, to correct the solution, or have to understand some of the reasons for failure, so as to better ensure timely solution, to avoid further expansion of the fault.

Welcome to yuhuan Kaitian hydraulic lubrication equipment Co., LTD. To negotiate and consult hydraulic lubrication pump.

Scan the QR code to read on your phone

Returns a list of

Recommended reading

Kaitian Lubrication to Lubricate Things Silently

 开天液压

WeChat

 开天液压

Wap

Add:No. 1, Building 45b, North Chuangrong Industrial City, Yucheng Sub-district, Yuhuan City, Zhejiang Province
Zip:317600
Tel:
0576-87234521
Fax:0576-87234522
Contact person: Manager Zhao
Mobile phone no.:
13967670889
Email:Office@cnkaitian.com
Web:www.kaitianyeya.com

<

Copyright © Yuhuan Kaitian Hydraulic Lubrication Equipment Co., Ltd.        浙ICP备16006032号        Power:300.cn

开天液压